Drift Design Method of Steel Moment Frames by using Column-Beam Strength Ratios and Unit-Load Method

Byung-Kwan Oh; Hyo-Seon Park; Se-Woon Choi

doi:10.7734/COSEIK.2016.29.6.563

All Issue

2016 Vol.29, Issue 6 Preview Page Next Page

Drift Design Method of Steel Moment Frames by using Column-Beam Strength Ratios and Unit-Load Method 기둥-보 휨강도비와 단위하중법을 이용한 철골모멘트골조의 강성설계기법

2016. pp. 563-569

PDF XML

Abstract

This paper presents the resizing method of columns and beams that considers column-to-beam strength ratios to simultaneously control the initial stiffness and ductility of steel moment frames. The proposed method minimizes the top-floor displacement of a structure while satisfying the constraint conditions with respect to the total structural weight and column-to-beam strength ratios. The design variable considered in this method is the sectional area of structural members, and the sequential quadratic programming(SQP) technique is used to obtain optimal results from the problem formulation. The unit load method is applied to determine the displacement participation factor of each member for the top floor lateral displacement; based on this, the sectional area of each member undergoes a resizing process to minimize the top-floor lateral displacement. Resizing members by using the displacement participation factor of each member leads to increasing the initial stiffness of the structure. Additionally, the proposed method enables the ductility control of a structure by adjusting the column-to-beam strength ratio. The applicability of the proposed optimal drift design method is validated by applying it to the steel moment frame example. As a result, it is confirmed that the initial stiffness and ductility could be controlled by the proposed method without the repetitive structural analysis and the increment of structural weights.

본 논문에서는 철골모멘트골조의 초기 강성과 연성을 동시에 조절하기 위해 기둥-보 휨강도비를 고려한 재분배 기법이 제시된다. 제 시되는 기법은 총 구조물량과 기둥-보 휨강도비에 대한 제약조건을 만족시키면서 구조물의 최상층의 변위를 최소화한다. 고려된 설계변 수는 구조부재의 단면적을 사용하며, 정식화된 문제로부터 최적의 결과를 얻기 위해 Sequential Quadratic Programming(SQP) 기법을 사 용한다. 최상층의 횡변위에 대한 각 부재의 변위기여도를 단위하중법을 통해 구하고, 이를 최상층의 횡변위가 감소하도록 각 부재의 단 면을 재설계한다. 각 부재의 변위기여도를 이용하여 부재의 단면을 재설계하는 과정은 구조물의 초기 강성을 향상시키는 효과를 가진다. 동시에, 제시된 기법은 기둥-보 휨강도비를 제약함으로써 구조물의 연성을 조절하도록 한다. 제시된 최적변위설계기법은 철골골조 예제 에 적용하여 적용성을 검증한다. 적용한 결과 제시된 기법을 통해 구조물의 초기강성과 연성능력이 조절되는 것을 확인할 수 있었다.

키워드

철골모멘트골조

강성설계

단위하중법

기둥-보 휨강도비

References

REFERENCES

M Al-Ansari and A Senouci, The Struct. Des. Tall & Special Build, Drift Optimization of High-rise Buildings in Earthquake Zones, 20(2); 208-222 (2011)

10.1002/tal.530

ANSI/AISC 341-05, Am. Inst. Steel Constr, Seismic Provisions for Structural Steel Buildings (2005)

S Atabay and FG Gulay, Expert Syst. Appl, The Study of the Effect of Changes in Cost of the Materials Used in 3-D Shear-Wall Reinforced Concrete Structures on the Optimum Dimensions, 36(3); 4331-4337 (2009)

10.1016/j.eswa.2008.05.039

AD Belegundu and TR Chandrupatla, Optimization Concepts and Applications in Engineering, Cambridge University Press. (2011)

M Bruneau, CM Uang and A Whittaker, Ductile Design of Steel Structures, USA. McGraw-Hill. (1997)

CM Chan and XK Zou, Earthq. Eng. & Struct. Dyn, Elastic and Inelastic Drift Performance Optimization for Reinforced Concrete Buildings under Earthquake Loads, 33(8); 929-950 (2004)

10.1002/eqe.385

SW Choi and HS Park, J. Comput. Struct. Eng. Inst. Korea, Inter-story Drift Design Method to Improve the Seismic Performance for Steel Moment Frames, 24; 707-714 (2011)

SW Choi, Y Kim, J Lee, K Hong and HS Park, J. Constr. Steel Res, MinimumColumn to Beam Strength Ratios for Beam–Hinge Mechanisms based on Multi-Objective Seismic Design, 88; 53-62 (2013)

10.1016/j.jcsr.2013.05.004

M El Semelawy, AO Nassef and AA El Damatty, Expert Syst Appl, Design of Prestressed Concrete Flat Slab using Modern Heuristic Optimization Techniques, 39(5); 5758-5766 (2012)

10.1016/j.eswa.2011.11.093

FEMA 273 NEHRP, Fed. Emerg. Manag. Agency, Guidelines for the Seismic Rehabilitation of Buildings (1997)

DA Foutch and SY Yun, J. Constr. Steel Res, Modeling of Steel Moment Frames for Seismic Loads, 58(5-8); 529-564 (2002)

10.1016/s0143-974x(01)00078-5

Y Gong, Y Xue, L Xu and DE rierson, J. Constr. Steel Res, Energy-based Design Optimization of Steel Building Frameworks using Nonlinear Response History Analysis, 68(1); 43-50 (2012)

10.1016/j.jcsr.2011.07.002

IBC 2015, International Code Council, International Building Code (2015)

KBC 2016, Architectural Institute of Korea, Korea Building Code (2016)

M Liu, SA Burns and YK Wen, Earthq. Eng. & Struct. Dyn, Multiobjective Optimization for Performance-Based Seismic Design of Steel Moment Frame Structures, 34(3); 289-306 (2005)

10.1002/eqe.426

M Liu, SA Burns and YK Wen, J. Struct. Eng, Genetic Algorithm Based Construction Conscious Minimum Weight Design of Seismic Steel Moment Resisting Frames, 132(1); 50-58 (2006)

10.1061/(asce)0733-9445(2006)132:1(50)

HS Park and JH Kwon, The Struct. Des. Tall & Special Build, Optimal Drift Design Model for Multi-Story Buildings Subjected to Dynamic Lateral Forces, 12(4); 317-333 (2003)

10.1002/tal.224

JH Seo, WK Song, YH Kwon, K Hong and HS Park, The Struct. Des. Tall & Special Build, Drift Design Model for High-rise Buildings Based on Resizing Algorithm with a Weight Control Factor, 17(3); 563-578 (2008)

10.1002/tal.366

JH Seo and HS Park, J. Comput. Struct. Eng. Inst. Korea, Design Method to Control Wind-Induced Vibration of High-Rise Buildings Using Resizing Algorithm, 23; 465-474 (2010)

B Taranath, Steel, Concrete and Composite Design of Tall Buildings, McGraw-Hill. (1998)

Information

Publisher :Computational Structural Engineering Institute of Korea
Publisher(Ko) :한국전산구조공학회
Journal Title :Journal of the Computational Structural Engineering Institute of Korea
Journal Title(Ko) :한국전산구조공학회 논문집
Volume : 29
No :6
Pages :563-569
Received Date : 2016-10-25
Revised Date : 2016-11-14
Accepted Date : 2016-11-15
DOI :https://doi.org/10.7734/COSEIK.2016.29.6.563

Journal of the Computational Structural Engineering Institute of Korea ISSN:1229-3059(Print) 2287-2302(Online) 한국전산구조공학회 논문집

All Issue

REFERENCES